-
Trailblazer/Trailboss 250 Top End Gasket Kit
Kit includes head, base, and exhaust gasket to rebuild the top end of your Polaris 250. Don’t ever re-use old gaskets when rebuilding your engine! High quality non-asbestos materials are used in kit. Includes all of the following top end gaskets shown in the photo including:
Head Gasket
Base Gasket
Exhaust GasketThis gasket kit fits the following models:
1990-2006 Trailblazer 250
1989-92 Trailboss 250
1989-92 Big Boss 250
2000-02 Xplorer 250
$24.95$22.46Trailblazer/Trailboss 250 Top End Gasket Kit
$24.95$22.46 -
Trailblazer Secondary Clutch Puller
The secondary clutch is supposed to slide right off the shaft. However, if neglected, the clutch will be rusted onto the shaft and you simply cannot get it off without this puller. Hardened steel puller is plated for corrosion resistance. 5.5″ overall length. Same as Polaris part number 2870913.
Fits all 1990-2013 Trailblazer 250/330/400 modelsSame as Polaris part number 2870913.
$24.95$22.46Trailblazer Secondary Clutch Puller
$24.95$22.46 -
Trailblazer Primary Clutch Puller
Brand new primary clutch puller for almost all 1985 and newer Polaris ATV’s and UTV’s using the P85 primary clutch. Hardened steel puller is plated for corrosion resistance. 10.25″ overall length and 3/4″-16 threads. Be sure to use a dab of grease on the end of the puller and threads to properly pull the clutch. Same as Polaris part number 2870506.
Fits all 1990-2013 Trailblazer 250/330/400 models
Same as Polaris part number 2870506.
$24.95$22.46Trailblazer Primary Clutch Puller
$24.95$22.46 -
Trailblazer Primary Clutch Bolt and Washers
Brand new primary clutch bolt and washers for many single cylinder Polaris ATV and UTV’s. Brand new high quality parts are exactly the same as the originals! These replace Polaris part numbers 5210748, 7512566, and 7575202. Includes one clutch bolt, one thick flat washer, and one star type washer. Fits the following models and more:
1990-2006 Trailblazer 250
2008-13 Trailblazer 330
Replaces Polaris Part Number: 5210748, 7512566, and 7575202
$8.95$8.06Trailblazer Primary Clutch Bolt and Washers
$8.95$8.06 -
Trailblazer Gates G-Force Workhorse Drive Belt
Quad Logic is now a Gates distributor for all your Polaris ATV and UTV belt needs! These belts are tried and true, torture tested for years. We trust them on all our machines and so should you. They are a much better value than the OEM Polaris belts but probably exceed the performance at the same time. This G-Series Workhorse belt is a perfect replacement and /or performance belt for your machine. The top cogs offer better cooling and the aramid cords make it extremely strong. The Gates G-Force Workhorse 20G4022 has increased strength and reliability. Replaces Polaris part number 3211077.
- Up to 2x the life of the G-Force Belt.
- 45% increased heat tolerance.
- Power for hauling heavy loads across aggressive terrain
- Improved durability, crack & wear-resistance.
FITS THE FOLLOWING MODEL(S):
1992-’13 Trailblazer 250/330/400’sREPLACES POLARIS PART NUMBER(S) 3211077 and 3211048
$84.95$76.46Trailblazer Gates G-Force Workhorse Drive Belt
$84.95$76.46 -
Trailblazer Exhaust Gasket Donut Seal
This exhaust gasket from Quad Logic is manufactured from a thick stainless steel mesh wrapped in an outer layer of graphite. It is designed to perform even better than the stock Polaris gasket. Exact replacement for your Polaris. Most Trailboss and Trailblazers use TWO gaskets total: one between the short head pipe and main pipe and another between the main pipe and the muffler. Be sure to order 2 if replacing both. Sold each. Replaces Polaris 5243517. Fits the following Polaris ATV models:
2008-13 Trail Blazer 330
2000-02 Trail Boss
2003-13 Trail Boss 330
2000-02 Xpedition 325/425
Replaces Polaris 5243517.
$9.99$8.99Trailblazer Exhaust Gasket Donut Seal
$9.99$8.99 -
Trailblazer Engine Mounting Nuts (6 PACK)
Brand new replacement engine mounting nuts for Polaris ATV models. These brand new flange hex flange nuts are brand new replacements for Polaris part number 7547108. These identical replacements are zinc coated for a durable finish and even include the factory applied thread locker on inside of the threads. We sell these nuts in a 6 pack. With many applications and other uses across all the Polaris machines be sure to check with the Polaris parts diagrams. The applications listed below show what machines use these nuts for engine mounting.
(Sold as a 6 PACK)
Check out Quad Logic for all your replacement Polaris hardware needs.
Fits the following models:
2001 Worker 500
1999-01 Xplorer 400
2000-02 Xpedition 325
2000-02 Xpedition 425
2003-13 Trail Boss 330
2008-13 Trail Blazer 330
Replaces Polaris Part Number: 7547108
We make every attempt to ensure every items fitment is accurate. We do the testing on each item before its listed for sale to ensure fitment and quality. Items may fit multiple years and models listed.Returns are subject to 15% restocking fee.$7.95$7.16Trailblazer Engine Mounting Nuts (6 PACK)
$7.95$7.16 -
Trailblazer 250 Clutch Outlet Tube Rubber Boot
Brand new clutch air outlet boot. Replace that old dried out cracked one with this new one. This boot fits between the clutch cover outlet and plastic tube (near your left leg). Replaces Polaris part number # 5411489.
FITS THE FOLLOWING MODELS(S):
2002-05 Trail Blazer 330 2002-05 Trail Boss 330 1998-99 Big Boss 500 1999 Worker 335 1999-01 Worker 500 2002 Xplorer 400 2004-05 ATP 330 2004-05 ATP 500 REPLACES POLARIS PART NUMBER(S): 5411489
$11.95$10.76Trailblazer 250 Clutch Outlet Tube Rubber Boot
$11.95$10.76 -
Trail Blazer Taillight Lens
Replace your broken rear taillight lens with this exact replacement. Fits and works just the like expensive factory lens. Replaces Polaris part number 4032085. Fits the following Polaris models:
1996-06 Trailblazer 250
2008-09 Trailblazer 330
2003 Trailblazer 400
1996-99 Sport 400
REPLACES POLARIS PART NUMBER(S): 4032085Shipping from Ramsey, Minnesota (USA) within 24 hours allows you to BUY WITH CONFIDENCE!
$10.95$9.86Trail Blazer Taillight Lens
$10.95$9.86 -
Trail Blazer 330 Rear Axle Retaining Ring
Brand new rear axle nut retaining ring clip. Brand new high quality part that is exactly the same as the original! Sold EACH. This replaces Polaris part number 7670160. Fits the following models and more:
2005-13 TRAIL BLAZER 330
Replaces Polaris Part Number: 7670160
$8.95$8.06Trail Blazer 330 Rear Axle Retaining Ring
$8.95$8.06 -
Trail Blazer (2004-2006) Fuel Tank Cap with Gauge
Know if it is time to fill up with the replacement fuel tank cap with gauge from Quad Logic! This replacement fuel cap will work on your 2004-2006 Polaris Trail Blazer.
Fits the following models:
2004-’06 Trail Blazer 250
Replaces Polaris part number: 2871441
$22.95$20.66Trail Blazer (2004-2006) Fuel Tank Cap with Gauge
$22.95$20.66 -
Sportsman Tie Rod End To Spindle Washers (4 PACK)
Brand new washers for your Polaris Sportsman. These washers are specifically used on the outer tie rod ends of models Polaris Sportsman models. These yellow zinc washers are an exact replacement for Polaris Part number 7556099. 2 washers are used each side of machine, 1 on top of spindle and 1 on the bottom as shown in pictures above. these are sold as a 4 pack so you can replace both sides of the machine.
This listing is for 4 washers only. No other hardware is included in the listing. Please check out Quad Logic for all your Polaris hardware needs.
Fits the following models and many more
2000 Sportsman 335
2000-19 Sportsman 500
2001-14 Sportsman 400
2002-07 Sportsman 700
2006-14 Sportsman 800
2014-22 Sportsman 570
2016-22 Sportsman 450
2020-22 Sportsman 850
2020-22 Sportsman 1000
REPLACES POLARIS PART NUMBER(S): 7556099
$6.95$6.26 -
Sportsman REAR Brake Caliper Piston
Replace that corroded caliper piston with this brand new unit from the original brake manufacturer. This is NOT a reproduction piston. Long lasting anodized finish. This piston will fit rear caliper part numbers 1910690, 1911075, 1910806.FITS THE FOLLOWING MODEL(S):
2003-05 Sportsman 4002006-07 Sportsman 4502003-09 Sportsman 5002003-05 Sportsman 6002002-07 Sportsman 7002005-09 Sportsman 8002008-13 Sportsman 800 6×6This kit will fit Polaris rear caliper part number 1910690, 1911075, 1910806.
$29.95$26.96Sportsman REAR Brake Caliper Piston
$29.95$26.96 -
Sportsman Ignition Keyswitch Repair Harness Pigtail
The connectors to the Polaris ATV ignition switches are prone to corroding and preventing the switch from working. Even the tab is brittle so they can easily break off and need to be replaced. Don’t buy the whole wire harness from Polaris!! We have this easy pigtail kit to splice in the new connector. This direct replacement plug fits a huge number of 2002 and newer Polaris ATV models and will get your ignition switch working again. Simply cut off the old harness and use the included butt connectors or solder the connections to the new pigtail. Our pigtail fits perfectly to the ignition switch and has a nice wire sheathing protecting the wires going into the plug. The wires are 6″ long so it can be fixed inside the headlight pod. Sold Each. Includes butt connectors and zip ties. Fits all 6 pin ignition switches such as Polaris part number 4010390, 4011002, 4012165, 4012166. Fits the models listed below and more:
2008-10 Sportsman 300
2002-14 Sportsman 400
2006-18 Sportsman 450
2002-13 Sportsman 500
2009-14 Sportsman 550
2014-18 Sportsman 570
2003-05 Sportsman 600
2002-07 Sportsman 700
2005-14 Sportsman 800
2009-17 Sportsman 8502010-19 Sportsman 850 Touring
2015-17 Sportsman 10002015-18 Sportsman 1000 Touring
2015 Sportsman ETXWorks with Polaris Part Number: 4010390, 4011002, 4012165, 4012166
$24.95$22.46Sportsman Ignition Keyswitch Repair Harness Pigtail
$24.95$22.46 -
Sportsman 800 Water Pump Seal
We’ve tooled up to offer you a great cost effective replacement to the OEM water pump seal. This seal is made to the exact same specifications as stock so you can be sure it will perform the same and save you money at the same time! Fits all 2005-14 Sportsman 800’s. (Including X2 and Touring models)
Replaces Polaris part number 3610075.
$34.95$31.46Sportsman 800 Water Pump Seal
$34.95$31.46 -
Sportsman 800 Water Pump Crankcase Oil Seal
This special Viton oil seal is located directly behind the mechanical water pump seal of most Sportsman twin cylinder motors. Make sure to replace it if you are getting coolant in the oil or you are changing the mechanical seal! Made to be equivalent to or better than the expensive OEM seal. Fits all 2005-15 Sportsman 800 models.
Replaces Polaris part #5412455 and 5411184.
$19.95$17.96Sportsman 800 Water Pump Crankcase Oil Seal
$19.95$17.96
- HOME
- Quad-Logic ATV Parts
- POLARIS RZR PARTS AND ACCESSORIES
- Polaris RZR 570 Parts and Accessories
- Polaris RZR 800 Parts and Accessories
- Polaris RZR 900 XP Parts and Accessories
- Polaris RZR 1000 XP Parts and Accessories
- Polaris RZR 1000 S Parts and Accessories
- Polaris RZR 900 Trail/XC/S Parts and Accessories
- RS1 Parts and Accessories
- RZR PRO XP
- Polaris RZR Turbo Parts and Accessories
- POLARIS RANGER PARTS AND ACCESSORIES
- POLARIS ATV PARTS AND ACCESSORIES
- Sportsman 400
- Polaris Sportsman 500 Parts and Accessories
- Polaris Sportsman 570 Parts and Accessories
- Polaris Sportsman 600 Parts and Accessories
- Polaris Sportsman 700 Parts and Accessories
- Polaris Sportsman 800 Parts and Accessories
- Polaris Sportsman 550/850/1000 XP Parts and Accessories
- Polaris Scrambler 500 Parts and Accessories
- Polaris Scrambler 850/1000 Parts and Accessories
- Polaris Trailblazer Parts and Accessories
- Polaris Magnum Parts and Accessories
- Polaris Ace Parts and Accessories
- CAN-AM PARTS AND ACCESSORIES
- POLARIS RZR PARTS AND ACCESSORIES
- ATV
- UTV
- SNOWMOBILE
- MOTORCYCLE
- LAWN & GARDEN
- Small Engine Parts
- 50% OFF PRODUCTS
- Checkout