| | |
 | Wilwood Brake Cylinder Kit for Polaris(Reference #525-200)
This master cylinder kit provides more braking power with less hand effort. Two finger brake lockup allows all required braking power still gives you a secure grip on the nadlebar.. For all Indy models with Polaris hydraulic brakes.
6 In Stock
$104.95
|
| |
|
Lever only for #525-200 Kit Above
$24.95
|
|
|
 | SLP Boost Bottle for Polaris Twins(Reference #SLPBB)
The SLP plastic Boost Bottle helps correct reed valve pressure balance to improve low to midrange driveability, throttle response, fuel economy and horsepower. A must for stock or modified twins. Air screw and/or pilot jet changes may be needed. Complete instructions included.
$33.95
|
| |
Boost Bottle
(Reference #200-159)
$34.95 Instructions | 700 XC/RMK 2001-05
800 XC/RMK 2000-05
14 In Stock | |
Boost Bottle
(Reference #200-146)
$34.95 Instructions | 600, 700 XC/SKS/RMK 1998-00
9 In Stock | |
Boost Bottle
(Reference #200-158)
$34.95 Instructions | 500, 600 w/VES 1999-02
5 In Stock | |
|
Oil Injection Cover for Polaris(Reference #200-OICOVER)
Fits oil injection Polaris models with Fugi engines. Plugs are available to maintain case volume.
|  |
| |
Oil Injection Cover
(Reference #200-806)
$12.95 | COVER
14 In Stock | |
Plug
(Reference #200-809)
$12.95 | PLUG (All except Storm)
15 In Stock | |
|
 | Suspension Drop Brackets(Reference #SUSP-BRKT)
High quality 1/4" thick 6061 aluminum. Drop measurement is from the bottom of the running board. Sold per pair.
|
| |
Suspension Drop Brackets
(Reference #560-405)
$118.95 | 1 3/4" Drop
1 In Stock
| |
Suspension Drop Brackets
(Reference #560-406)
$118.95 | 3 1/4" Drop
4 In Stock
| |
Suspension Drop Brackets
(Reference #560-409)
$118.95 | 4 1/2" Drop
2 In Stock
| |
Suspension Drop Brackets
(Reference #560-404)
$118.95 | 5" Drop
3 In Stock
| |
|
Yamaha Apex Drop Brackets(Reference #560-403)
Fits 2006-10
Save 6.5 lbs
Direct bolt on - replaces heavy stock brackets
Same drop as stock brackets
3 In Stock
$142.95
|
|
|
REV XP Drop Brackets(Reference #560-401)
Fits Rev XP Chassis 2008-10
1 1/2" drop
Mounting hardware included
2 In Stock
$142.95
|
|
|
'Add On' Drop Bracket(Reference #560-402)
1" to 2" drop Bolts to original drop bracket Fits most sleds Easy installation Necessary hardware included Sold per pair
3 In Stock
$71.95
|  |
| |
|
 | Air Vent(Reference #200-257)
This new stream-lined vent adds a sporty appearance, but most important, it removes unwanted hot underhood air that robs performance. Can be located on any flat or near flat surface for hot air excaped or reversed for cold air inlet. Supplied in black but is paintable. Universal fit. 3 1/4" x 12 1/4"
2 In Stock
$17.95
|
| |
|
Yamaha Front End Shim Kit(Reference #100-650)
Is the steering on your Yamaha snowmobile non-responsive and loose? Use the shim kit to tighten it up! This kit includes spacer washers to replace the original manufacturere spacer washer on the Yamaha 1980-97 TSS front suspension when they get worn. It also includes (6) .005, (6) .010 and (6) .015 stainless steel shims to take out the side play in your front scissor arms, even on new sleds.
Instruction Sheet
10 In Stock
$33.95
|  |
| |
|
Chromoly Handlebars(Reference #900-CMH)
4130 Chromoly steel
Snowmobile specific bends offer better comfort
Fits 7/8" handlebar clamps
No rise flat design offers more surface area for controls
Guide lines on ends of bar for narrowing handlebar to a custom width
Accepts standard hooks
Available in black only
|  |
| |
Chromoly Handlebar
(Reference #900-855)
$33.95 | 10o Pull Back - 31 1/2"
0 In Stock
| |
Chromoly Handlebar
(Reference #900-843)
$33.95 | 15o Pull Back - 29 1/4"
(top photo)
8 In Stock
| |
Chromoly Handlebar
(Reference #900-844)
$33.95 | Race Bend
10o Pull Back - 30"
(bottom photo)
16 In Stock
| |
|
 | Aluminum Rise Handlebars(Reference #9007)
2014 heat treated aluminum has superior strength to resist bending Snowmobile specific 10 degree bend offers increased comfort Fits 7/8" handlebar clamps Crossbar has pre drilled holes for stud or bolt mounted style of mountain / Grab strap (not included) Guide lines on ends of bar for narrowing handlebar to a custom width Black bar pad included Black color only
|
| |
Handlebar
(Reference #900849)
$56.95 | 7" Rise
0 In Stock
| |
Handlebar
(Reference #900850)
$56.95 | 5" Rise
0 In Stock
| |
Grab Strap
(Reference #13580(a))
$33.95
|
Optional Grab Strap
| |
|
Tapered Aluminum Handlebars(Reference #900-TAPER)
7075-T6 heat treated aircraft aluminum Tapered wall aluminum flexes to reduce rider fatigue and arm pump Tapered wall construction offers the strongest snowmobile handlebar available Clamp surface is 1 1/8" and tapers down to 7/8" to fit standard controls and grips Black snowmobile bar pad included 1 1/8" oversized clamp kit or 1 1/8" size risers are required to mount to snowmobile (not included) Custom snowmobile specific bends offer more comfort than stock handlebars Guide lines on ends of bar for narrowing handlebar to a custom width
|  |
| |
Handlebar
(Reference #900851)
$66.95 | Backcountry Bend
29" with 3 1/4" Rise & 14o Pullback
1 In Stock
| |
Handlebar
(Reference #900852)
$66.95 | Backcountry Bend
29 1/4" with 15o Pullback
2 In Stock
| |
Handlebar
(Reference #900853)
$66.95 | Backcountry Bend
31 1/2" with 10o Pullback
2 In Stock
| |
Handlebar
(Reference #900854)
$66.95 | Race Bend
30" with 2mm Rise & 10o Pullback
0 In Stock
| |
Clamp Kit
(Reference #900856)
$27.95 | 1 1/8" Clamp Kit
2 In Stock
| |
|
 | Riser Bars(Reference #900-BARS)
Chrome moly steel Provides more comfort Accommodates bar ends Strong and lightweight Fits most snowmobiles Black powder coat finish
NOTE: Check cable & wire length before ordering. Cables and wires may need to be longer on some models
|
| |
2" Riser Bar
(Reference #900-841)
$85.95 | 2" Rise
1 In Stock
| |
4" Riser Bar
(Reference #900-842)
$94.95 | 4" Rise
3 In Stock
| |
|
 | Hi-Compression Head Gasket(Reference #336-222)
For Polaris 650 Indy - Fugi Engines
.044 thick head gasket
Sold individually
3 required
2 In Stock
$12.95
|
| |
|
Aurora Rod Ends(Reference #RODENDS)
HEAVY DUTY - High performance Aurora teflon lined zinc plated aviation style rod ends for tie rods and radius rods. The teflon lining keeps the joints tight and eliminates free play in the steering and front end. Supplied with jam nuts. AIRCRAFT QUALITY.
|  |
| |
Rod Set
(Reference #202-225)
$175.95 | COMPLETE STEERING & RADIUS ROD SET
(POLARIS)
10 In Stock
| |
Rod Set
(Reference #202-250)
$79.95 | RADIUS ROD SET
(POLARIS)
10 In Stock
| |
Rod Set
(Reference #202-222)
$87.00 | STEERING SET (6 3/8")
10 In Stock | |
Rod End
(Reference #202-230)
$15.95 | 3/8" RH Rod End
30 In Stock
| |
Rod End
(Reference #202-232)
$18.50 | 7/16" RH Rod End
37 In Stock
| |
Rod End
(Reference #202-234)
$21.95 | 1/2" RH Rod End
40 In Stock
| |
Rod End
(Reference #202-240)
$15.95 | 3/8" LH Rod End
28 In Stock
| |
Rod End
(Reference #202-242)
$18.50 | 7/16" LH Rod End
11 In Stock
| |
Rod End
(Reference #202-244)
$21.95 | 1/2" LH Rod End
6 In Stock
| |
|
Polaris Steering Block(Reference #900-558)
Steering block and the upper support bushing for Polaris steering columns will permanently eliminate handlebar play. The block is made of billet aluminum and the bushing is a durable plastic. The whole assembly is strong and lightweight. 2 piece for easy installation. Fits all with 7/8" steering post except Edge and Pro X.
26 In Stock
$49.95
|  |
| |
