|  | Rox Pivot Risers
Ref: ROX-RISER
Based on the Rox Speed FX patented pivoting riser, these risers work on any snowmobile, ATV, motorcycles, etc. Dual rotation points allow rider to select optimum riding positions Check your cables first to see how high you can raise your bars. Three heights available - 2", 3.5" & 5"
| | |
|
|
Rox Pivot Riser
Ref: 300201
2" Riser
| 13 In Stock
|
|
Rox Pivot Riser
Ref: 300204
3.5" Riser
| 9 In Stock
|
|
Rox Pivot Riser
Ref: 300205
5" Riser
| 3 In Stock
|
|
|  | Pivoting Risers
Ref: 300-PRK
Dual pivoting adjustability allows you to position handlebars where you want them Revolutionary mounting design resists riser slipping during hard hits or aggressive riding Inserts included allow risers to work on stock 7/8" handlebars and oversize 1 1/8" handlebars Aircraft aluminum resists bending or twisting For use with pivot style steering posts or flat top steering posts with pivot tube Anodized black color finish
NOTE: Double check length of cables and brake lines for proper fit. Extended length cables or brake lines may be required for proper operation | | |
|
Pivoting Riser
Ref: 300-190
2" Riser
| 4 In Stock
|
|
Pivoting Riser
Ref: 300-192
4" Riser
| 10 In Stock
|
|
Pivoting Riser
Ref: 300-194
6" Riser
| 1 In Stock
|
|
Pivoting Riser
Ref: 300-196
8" Riser
| 8 In Stock
|
|
|  | Steering Post Pivot Adapter
Ref: PIVOT-ADP
Converts a flat steering post to a double pivot style postChromoly and hi temp steel constructionSimple bolt on designWorks with RSI Risers or other 2 piece aftermarket risers. PowerMadd adjustable one piece risers will not work with this Pivot AdapterAdds 1/2" of rise
NOTE: Since these pivot adapters put the risers on the outside of the steering post plate, the widths of the clamping surface varies. Double check the clamp surface area width on your stock bars to make sure it is wide enough for the risers to clamp down on a flat surface and not into the curve of the handlebar.
Handlebar clamp surface width minimums for RSI Risers:Ski-Doo - 4 3/8"Arctic Cat & Polaris - 4 9/16"Yamaha - 4 13/16" | | |
|
Steering Post Pivot Adapter
Ref: 300150
Arctic Cat
(except telescopic steering post)
| 4 In Stock
|
|
Steering Post Pivot Adapter
Ref: 300151
Polaris
| 1 In Stock
|
|
Steering Post Pivot Adapter
Ref: 300152
Ski-Doo
2000 and newer non Rev
| 2 In Stock
|
|
Steering Post Pivot Adapter
Ref: 300153
Ski-Doo Rev
| 6 In Stock
|
|
Steering Post Pivot Adapter
Ref: 300154
Yamaha
| 3 In Stock
|
|
|  | Handlebar Riser Kits
Ref: HBRISER
NON PIVOT STYLE. Increase the height of your handlebars for comfort and additional knee room. Black in color. Be sure you have enough throttle and brake line length before ordering 2", 3" or 4" risers. Available for Arctic Cat Polaris, Ski-Doo and Yamaha - Make your selection below. Installation Instructions | | |
|
|
|
Riser Kit - 2"
Ref: 15504
SKI-DOO
| 14 In Stock
|
|
Riser Kit - 2"
Ref: 15505
YAMAHA
NOT APEX OR NYTRO
| 7 In Stock
|
|
|
|
Riser Kit - 3"
Ref: 15506
ARCTIC CAT thru '99
ALL POLARIS
| 16 In Stock
|
|
Riser Kit - 3"
Ref: 15507
SKI-DOO
| 3 In Stock
|
|
Riser Kit - 3"
Ref: 15508
YAMAHA
NOT APEX OR NYTRO
| 3 In Stock
|
|
Riser Kit - 3"
Ref: 15511
ARCTIC CAT '00 & newer
| 8 In Stock
|
|
|
Riser Kit - 4"
Ref: 15517
ARCTIC CAT thru '99
ALL POLARIS
| 6 In Stock
|
|
Riser Kit - 4"
Ref: 15520
ARCTIC CAT '00 & newer
| 3 In Stock
|
|
Riser Kit - 4"
Ref: 15518
SKI-DOO
| 4 In Stock
|
|
|  | Sportech Bar Riser
Ref: STRISER
For better control, increased performance and comfort! Billet aluminum handlebar riser kits for Polaris, Arctic Cat, Ski-Doo and Yamaha. Raising your handlebars increases control over rough terrain and puts your arms in a comfortable, more natural position. Each kit comes complete with instructions and hardware. Available in natural aluminum finish only. | | |
|
Riser Kit
Ref: 300-173
2" Riser
ARCTIC CAT & POLARIS
| 2 In Stock
|
|
Riser Kit
Ref: 300-174
3" Riser
ARCTIC CAT & POLARIS
| 1 In Stock
|
|
Riser Kit
Ref: 300-175
2" Riser
SKI-DOO
| 1 In Stock
|
|
|  | Bar Riser Pad
Ref: 300-177
Dress up your bars and protect yourself at the same time with this cool looking Bar Riser Pad. This "moto" style pad is made from low density foam and is wrapped in a waterproof vinyl cover with hot Sportech Racing graphics. Must be used with Sportech Bar Risers. Black with orange and gray graphics. | | |
|
|  | PowerRiser 325
Ref: 325-RISER
Pivoting riserOne piece solid aluminum design for superior strength3.25" wide fits 7/8" bar clamps on all snowmobile and Bombardier and Polaris ATVsProvides dual pivot points allowing for bars to be positioned front to back and rotated up or down2" rise will work on most snowmobiles with no cable modification, ATVs should check available cable slack
NOTE: Models with one piece original bar clamps will not work with this riser. Replace one piece bar clamp with a set (2) of individual bar clamps | | |
|
Power Riser 325
Ref: 15420
Power Riser 325
| 2 In Stock
|
|
Individual Bar Clamps
Ref: 15470
Individual Bar Clamps(Set of 2)
| 6 In Stock
|
|
|  | Angled Handlebar Risers
Ref: ANG-BARRISER
Raises handlebars straight up from center of steering post6061 T-6 aluminum constructionOffers increased comfort for mountain or trail ridingMost sleds will allow 2" or 3" without any cable extensionsAnodized finishFits stock 7/8" handlebarsAvailable in black only
NOTE: Check your cable and brake line length before ordering | | |
|
| | Angled Bar Riser - 15o Angle Fits: Arctic Cat M-Series and Crossfires thru 2008
Polaris IQ 2009-10 with Flat Plate Steering Post |
|
Angled Handlebar Riser
Ref: 300-188
15o - 2"
| 5 In Stock
|
|
Angled Handlebar Riser
Ref: 300-189
15o - 3"
| 5 In Stock
|
|
Angled Handlebar Riser
Ref: 300-169
15o - 4"
| 1 In Stock
|
|
| | Angled Bar Riser - 30o Angle Fits: Polaris thru 2008
Ski-Doo Rev & ZX Chassis
Arctic Cat thru 2008 (except M-Series and Crossfire)
Yamaha Mtn Max SX, SRX & Viper |
|
Angled Handlebar Riser
Ref: 300-186
30o - 2"
| 5 In Stock
|
|
Angled Handlebar Riser
Ref: 300-187
30o - 3"
| 10 In Stock
|
|
Angled Handlebar Riser
Ref: 300-168
30o - 4"
| 10 In Stock
|
|
|  | Rox Height Adjustable Handlebar Risers
Ref: HA-RISER
ELITE SERIES - Fits Standard 7/8" or 1 1/8" Aluminum FatbarsRox Adjustable Risers take the guess work out of deciding which size to buy. Now you can choose the range of adjustment or height you want: 4" to 6" or 6" to 8.25". Height Adjustable Risers give you the option of fitting one sled to multiple riders in minutes Designed to replace OEM pivoting riser blocks. CNC machined from billet 6061 T6 aluminum and clear anodized. PATENT PENDINGModels with flat top steering post require a pivot tube (#300-185) available below - not included with riser.
| | |
|
Height Adjustable Riser
Ref: 300-207
4" to 6" Riser-Wrenchless lever kit INCLUDED
| 9 In Stock
|
|
Height Adjustable Riser
Ref: 300-208
6" to 8.25" Riser - Wrenchless lever kit INCLUDED
| 15 In Stock
|
|
|  | Wrenchless Levers
Ref: 300-198
FOR ROX HEIGHT ADJUSTABLE RISERS (above)
Designed for quick and easy adjustment on the trail without the need for tools or removing your gloves. | | |
|
|  | Pivot Tube
Ref: 300-185
5 1/2" tube converts stock flat style steering post to a pivot style steering post for using a pivot style handlebar riser.Clamps into stock 7/8" handlebar clamps.Positions pivoting style risers on outside of stock handlebar clamps
NOTE: Double check handlebar clamping surface width to verify riser/pivot tube combination fits correctly. | | |
|
|  | Rox Anti-Vibration Pivoting Handlebar Riser - 2"
Ref: ROX-AVR
Anti-Vibe design reduces vibration in bars at high RPM's and provides a shock dampening feature to protect components and rider during harsh impacts. Adjustable - Dual rotation points makes Rox Handlebar Risers selectively adjustable forward and back, allowing you to fit your handlebars to your preferred riding position. Universal - With its two piece design, Rox Riser will install on virtually any snowmobile that has clamps to hold the handlebars. CNC machined from billet 6061 T6 aluminum anodized gold. Patent #US 6,920,806 BZ
| | |
|
Rox Anti-Vibration Pivoting Riser
Ref: 300-206
Elite Series
Fits standard 7/8" or 1 1/8" Aluminum Fatbars
| 6 In Stock
|
|
|  | Articulating Bar Riser
Ref: ABRISER
This universal, aluminum handlebar riser kit will fit most snowmobiles made today. Sportech A.B.R. kits feature perfectly matched riser arms, bar clamps and adaptor bar for a tight, uncompromising fit on your bars. This kit raises your bars to a more comfortable position and allows you to adjust your bars horizontally to fit your riding style. Each kit comes complete with instructions and hardware. Available in natural aluminum finish only. A TRULY adjustable snowmobile handlebar riser system offering increased bar height and full articulated radial adjustment. Be sure you have enough throttle and brake cable length before ordering. | | |
|
ABR Kit
Ref: 40127010
2" Riser
| 3 In Stock
|
|
ABR Kit
Ref: 40127011
3" Riser
| 2 In Stock
|
|
|
|  | ABR Pad
Ref: 50107022
This "moto" style pad is made from low density foam and is wrapped in a waterproof vinyl cover with hot Sportech Racing graphics. Must be used with Sportech A.B.R . Black with orange and gray graphics. | | |
|
|  | Handlebar Riser - Pivot Style Block
Ref: PIVOTRISER
Customize your handlebar height by replacing your riser to raise or lower your handlebarsMachined from 6061-T6 aluminumPivot Style Risers will directly replace OEM Pivot Style Risers that come on Arctic Cat, Polaris & Ski-Doo snowmobilesSome snowmobiles may need the throttle cable extension kitNOTE: Snowmobiles not currently equipped with Pivot Style Riser Blocks need to use a Pivot Adapter Kit (below)Utilizes existing bolts and clamps4.25" wide
NOTE: Yamaha requires the use of a pivot adapter kit
NOTE: Will not fit Polaris models with narrow pivot riser blocks: 2003 800 RMK; 2004 600, 700, 800 RMK; 2007-08 RMKs & Dragon (See Polaris Narrow Risers listed below for these models)
Instruction Sheet | | |
|
|
Riser Kit - 2"
Ref: 15539
Arctic Cat & Yamaha
| 11 In Stock
|
|
Riser Kit - 2"
Ref: 15540
Polaris
| 2 In Stock
|
|
|
|
Riser Kit - 4"
Ref: 15527
Arctic Cat & Yamaha
| 2 In Stock
|
|
|
Riser Kit - 4"
Ref: 15529
Ski-Doo
| 8 In Stock
|
|
|
Riser Kit - 6"
Ref: 15530
Arctic Cat & Yamaha
| 7 In Stock
|
|
Riser Kit - 6"
Ref: 15531
Polaris
| 3 In Stock
|
|
Riser Kit - 6"
Ref: 15532
Ski-Doo
| 1 In Stock
|
|
|
8" Riser Kit
Ref: 15533
Arctic Cat & Yamaha
| 2 In Stock
|
|
8" Riser Kit
Ref: 15534
Polaris
| 6 In Stock
|
|
8" Riser Kit
Ref: 15535
Ski-Doo
| 2 In Stock
|
|
|
10" Riser Kit
Ref: 15536
Arctic Cat & Yamaha
| 4 In Stock
|
|
10" Riser Kit
Ref: 15537
Polaris
| 1 In Stock
|
|
10" Riser Kit
Ref: 15538
Ski-Doo
| 4 In Stock
|
|
| | Polaris Narrow Risers Fits Polaris narrow riser (3.5") models: 2003 800 RMK; 2004 600, 700, 800 RMK; 2007-08 RMKs & Dragon |
|
4.5" Riser Kit
Ref: 15554
4.5" Riser
| 3 In Stock
|
|
|
8.5" Riser Kit
Ref: 15558
8.5" Riser
| 3 In Stock
|
|
|  | Yamaha Nytro Riser - 4"
Ref: 15564
Replaces stock riser and adds an additional 2" of height with no modifications. | | |
|
|  | Pivot Adapter Kit
Ref: 1558ADAPTER
PIVOT STYLE RISER BLOCK CONVERSION KITAllows the handlebar and rider to move forward, optimizing the center of gravity and improving handling and control (like the Ski-Doo MXZ-REV chassis concept)Handlebars can be pivoted forward or back from original stock positionPivot Adapter raises bars and additional 1.25"Choose a riser block height of 2", 4", 6", 8" or 10" (above)Machined from 6061-T6 aluminum
Instruction Sheet | | |
|
Pivot Adapter Kit
Ref: 15580
Arctic Cat
| 4 In Stock
|
|
Pivot Adapter Kit
Ref: 15581
Polaris
| 11 In Stock
|
|
Pivot Adapter Kit
Ref: 15582
Ski-Doo
| 6 In Stock
|
|
|
|  | Universal Pivoting Riser System
Ref: PRS-UNIVERSAL
3.25" wideWorks on all brands of snowmobiles with flat steering post and at least 3.25" of straight handlebar.Universal Pivoting Riser raises bars 3" and can be used without additional riser blocksDual pivot points allow for bars to be positioned front to back and rotated up or down.Use optional Extension Blocks to increase bar height an additional 1", 2", 3" or 6". | | |
|
Universal Pivot Adaptor / Riser
Ref: 15400
Universal 3" Pivot Adaptor / Riser
| 12 In Stock
|
|
Universal Extension Block 1"
Ref: 15401
1" Extension Block
| 3 In Stock
|
|
Universal Extension Block 2"
Ref: 15402
2" Extension Block
| 4 In Stock
|
|
Universal Extension Block 3"
Ref: 15403
3" Extension Block
| 2 In Stock
|
|
|  | 1 1/8" Handlebar Mount Kit
Ref: 900856
Universal mounting kit allows oversized 1 1/8" handlebars to be installed Works on most OEM & aftermarket risers Can be mounted to a flat plate style steering post Simple bolt on design 6061 T-6 aluminum with a black anodized finish Also fits ATVs and motorcycles | | |
|
|  | Throttle Cable Extension Kit
Ref: THEXT-KIT
Finally a well-engineered system to allow you to raise your handlebars up to 10"Extension for your throttle cable when installing riser blocksInline adjuster to fine tune cable tension and slackNo modification required! | | |
|
Throttle Cable Extension Kit
Ref: 13592
Arctic Cat**, Polaris
& Ski-Doo
**Will not work on '07-11 F, M & CF Series - Instruction Sheet
| 20 In Stock
|
|
Throttle Cable Extension Kit
Ref: 13595
Yamaha - 4 Stroke Models
Will not work on dual cable 2 stroke models
| 11 In Stock
|
|
|  | Extended Length Brake Lines
Ref: BL-EXT
Raising the bar just got easier! Riser blocks are great for getting your bars to the right height, but many times raising your bars over 4 inches requires an extended brake line. Extended brake lines are made with extra tight stainless braided lines using a Teflon smooth bore liner which reduces line expansion to almost zero. All lines have a protective coating consisting of a UV protected PVC clear coat. | | |
|
| | Extended Length Brake Line
Ref: 15602
ARCTIC CAT Arctic Cat 1994-06 / Firecat 2003-06 / M Series 2005-06
Overall Length is 43.5" | | |
|
| | Extended Length Brake Line
Ref: 421-001
ARCTIC CAT '07-11
Overall Length is 43.5" | | |
|
| | Extended Length Brake Line
Ref: 421002
ARCTIC CAT '12 | | |
|
| | Extended Length Brake Line
Ref: 15604
POLARIS (except Pro-X, '00-03 RMK's & Gen II models with 90o caliper fitting)
Overall Length is 37" | | |
|
| | Extended Length Brake Line
Ref: 15605
POLARIS IQ / Fusion '06-09 (except Dragon RMK and Assault 2009-10 with Pro Taper Bars) / Pro-X 2006 & newer
Overall Length is 41" | | |
|
| | Extended Length Brake Line
Ref: 15616
POLARIS 2000-03 RMK / Gen II Models with 90 degree caliper fitting
overall length is 37" | | |
|
| | Extended Length Brake Line
Ref: 15606
SKI-DOO F2000 & CK3
Overall Length is 39" | | |
|
| | Extended Length Brake Line
Ref: 15607
SKI-DOO ZX MODEL
Overall Length is 35" | | |
|
| | Extended Length Brake Line
Ref: 15608
SKI-DOO REV (except '08-09 XP)
Overall Length is 42" | | |
|
| | Extended Length Brake Line
Ref: 15615
SKI-DOO REV XP
Overall Length is 44" | | |
|
| | Extended Length Brake Line
Ref: 15609
YAMAHA 1997-04 SX, VMax, Mtn Max, Viper
Overall Length is 37" | | |
|
| | Extended Length Brake Line
Ref: 15610
YAMAHA RX 2003-04 / RX Warrior 2004
Overall Length is 43.5 | | |
|
| | Extended Length Brake Line
Ref: 15611
YAMAHA SX, Venture '04 / RX, Warrior '05 / SX Venom, SX Viper '05 / Apex '06
POLARIS 2009-10 Assault & Dragon with Pro Taper Bars
overall length is 36.5" | | |
|
| | Extended Length Brake Line
Ref: 421-006
YAMAHA Phazer 2007-12
Overall Length is 41" | | |
|
| | Extended Length Brake Line
Ref: 421-007
YAMAHA Nytro RTX Trail 2009-12
Overall Length is 50" | | |
|
| | Extended Length Brake Line
Ref: 15614
YAMAHA Nytro MTX Mountain 2008-09
Overall Length is 57" | | |
|
|  | Extended Throttle Cables
Ref: EXT-TC
Eliminates the need for a throttle cable extensionA must have when using taller handlebar risers and wider handlebarsDirect OEM replacement for stockStainless steel braided top sections for a custom look (except 410-417)8" longer than stock | | |
|
| | Extended Throttle Cable
Ref: 410-411
2004 & Older Arctic 600, 800, 900 w/Rack Carbs
2001-02 Ski-Doo w/Rack Carbs | | |
|
| | Extended Throttle Cable
Ref: 410-415
Arctic Cat M Series 2006 & Older | | |
|
| | Extended Throttle Cable
Ref: 410-416
Arctic Cat M Series 2007 & Newer | | |
|
| | Extended Throttle Cable
Ref: 410-412
'00 & Newer Polaris XC, RMK 600, 700, 800 w/Rack Carbs
2006 & Newer Polaris RMK 600 HO w/Rack Carbs | | |
|
| | Extended Throttle Cable
Ref: 410-413
'03 & Newer Ski-Doo 600, 700, 800 w/Rack Carbs | | |
|
| | Extended Throttle Cable
Ref: 410-414
Yamaha Mtn Max 600,700 / Viper thru '02 / SRX700 / XTC / XT / VMax
NOTE: This is a dual cable - 1 for oil injection & 1 for throttle | | |
|
| | Extended Throttle Cable
Ref: 410-417
Yamaha Apex | | |
|
| | 8" Extended Throttle Cables Direct replacement for stock
Economical price |
|
| | Extended Throttle Cable
Ref: 410905
Arctic Cat M Series 2007 & Newer | | |
|
| | Extended Throttle Cable
Ref: 410901
'00 & Newer Polaris XC, RMK 600, 700, 800 w/Rack Carbs
2006 & Newer Polaris RMK 600 HO w/Rack Carbs | | |
|
| | Extended Throttle Cable
Ref: 410904
'03 & Newer Ski-Doo 600, 700, 800 w/Rack Carbs | | |
|
| | Extended Throttle Cable
Ref: 410902
Yamaha Mtn Max 600,700 / Viper thru '02 / SRX700 / XTC / XT / VMax
NOTE: This is a dual cable - 1 for oil injection & 1 for throttle | | |
|
Email
Blog
Facebook
Twitter
LinkedIn
Google+