| | |
 | Exhaust Snow Deflector Ref: 090-02
When riding in deep snow, the exhaust outlet can become partially plugged causing reduced performance and even bogging. The universal snow deflector creates a trench in the snow allowing free flow for the exhaust. It will fit most snowmobiles. The deflector requires a flat mounting area of 1" x 3 1/2", just forward of the exhaust outlet.
5 In Stock
$18.95
|
|
|
Spark Plug Indexing Washers Ref: 245INDEX
Have you ever noticed when removing your spark plugs that one side of the tip is burning lean while the other side appears to be rich. Here's why…take a look at your transfer ports, they are all directed to pack the charge on the intake side of your cylinder. When you index your plugs you are aligning the open end of your electrode on your spark plug toward the intake port of your cylinder by using certain thicknesses of washers to achieve this. Gain performance, fuel mileage and plug life. Kit contains sets of 4 different thickness washers and complete instructions. Available for 2 and 3 cylinder - make your choice below.
Installation Instructions
|  |
|
Indexing Washers
Ref: 245-500
$9.95 | TWIN CYLINDER
37 In Stock |
|
Indexing Washers
Ref: 245-510
$14.95 | THREE CYLINDER
17 In Stock |
|
|
 | Power Breather Ref: 200-594
D&D's latest Arctic Cat power accessory. Designed to give carbureted Cats the extra edge to smoke the competition! On some models, the Power Breather can produce gains up to 6 horsepower. Fits all Arctic Cats with tool box top airbox. Carbureted models only - not for EFI. Power Breather is a replacement airbox top with tool box and foam filter air openings. Easy installation. Available in black only. Fits 1997-01 models.
Installation Instructions
2 In Stock
$94.95
|
|
|
Headlight Elimination Kit Ref: HL-EKIT
Virtually indestructable, these headlight replacements have and OEM fit and save weight. Comes with everything to install! Vented kits have screens for extra cooling.
Fits 2005-11 M Series & Crossfires
|  |
|
Headlight Elimination Kit
Ref: 20030
$37.95 | Non Vented
2 In Stock |
|
Headlight Elimination Kit
Ref: 20030V
$56.95 | Vented
2 In Stock |
|
|
 | Black Boxx Cold Air Intake System Ref: 50044
Arctic Cat
Cold air intake system which removes 8 lbs of unwanted weight. Exclusive air mesh filtering and chamber separator to give you filtered and separated cold air from underhood engine heat. Suggested use of fuel management system to correct air/fuel mixture due to increased air flow. A must for any big bore engine and for the serious mountain rider.
Fits: Firecats 2003-06; M Series, Crossfire models 2005-08
3 In Stock
$171.95
|
|
|
Powder Valves Ref: PDR-VALVE
These trick flapper valves are installed in the air box to provide additional airflow to the engine. They are activated by air box vacuum. When the stock intake begins to plug in deep powder snow conditions, these valves open to deliver the necessary air flow that the engine demands. This substantially improves consistency when running in deep powder snow conditions. Sold per pair
|  |
|
Powder Valves Ref: 14-134
Ski Doo Rev XP 800
2 In Stock
$51.95
|
|
Powder Valves Ref: 14-132
Polaris 600, 700, 800 HO IQ/IQ RMK '06-10
(NOT for Polaris race chassis)
2 In Stock
$51.95
|
|
Powder Valves Ref: 14-136
Polaris 2010-12 Rush & Pro Ride
2 In Stock
$51.95
|
|
|
Powder Snow Pre-Filter Kit Ref: 14-PFK
FOR POLARIS IQ RMK & IQ SWITCHBACK
This Powder Snow Pre-Filter kit increases intake surface area for increased performance. It also eliminates the stock foam filters that are prone to falling out. The pre-filter securely fastens to the hood to provide a more positive seal for improved cold air intake with less chance of snow ingestion through intake vents. This kit features a brushed aluminum grate and pre-filter material that repels snow and water, yet maintains high air flow.
|  |
|
Powder Snow Pre-Filter Kit Ref: 14-227
All IQ Models 2005-08 (except 2008 700/800 RMK)
All IQ Touring, FST and 550/600 Shift Short Track 2009-12
7 In Stock
$48.95
|
|
Powder Snow Pre-Filter Kit Ref: 14-229
All IQ Models '09-12 (except Touring, FST, 550/600 Shift Short Track & Rush)
700, 800 CFI RMK '08
7 In Stock
$56.95
|
|
|
 | Hot Air Elimination Kit Ref: HAE-KIT
FOR POLARIS IQ RMK, IQ SWITCHBACK AND FUSION
SLP Hot Air Elimination Kits help reduce underhood hot air to maintain higher horsepower by delivery additional cold air and hot air escape from the chassis. The kit for the left side helps to keep the clutches running cool, which considerably reduces the chance for performance loss due to heat saturation and improves belt life. The kit for the right side helps to reduce underhood heat given off by the exhaust system. Vents have a powder snow pre-filter that repels snow and water, yet allows air to paas through. These vents are sold in kits for the right and left side. Each kit contains one air inlet grate, on outlet grage, reuqired fasteners and detailed instructions.
|
|
Hot Air Elimination Kit - Right
Ref: 32-529
$62.95 | RIGHT SIDE2006 600 HO Fusion2005-06 700/900 Fusion
Instruction Sheet
2 In Stock |
|
Hot Air Elimination Kit - Left
Ref: 32-528
$62.95 | LEFT SIDE2005-06 700/900 Fusion
Instruction Sheet
2 In Stock |
|
Hot Air Elimination Kit - Left
Ref: 32-522
$62.95
Instruction Sheet | LEFT SIDE2005-06 700/900 RMK/Switchback/FST
8 In Stock |
|
Hot Air Elimination Kit - Right
Ref: 32-523
$62.95
Instruction Sheet | RIGHT SIDE2005-06 700/900 RMK/Switchback/FST600 HO RMK/Switchback2007-11 IQ Models
(except FST & Rush)
16 In Stock |
|
Hot Air Elimination Kit - Left
Ref: 32-534
$62.95 | LEFT SIDE600 HO RMK/Switchback2007-11 IQ Models
(except FST & Rush)
Instruction Sheet
16 In Stock |
|
|
 | Hot Air Elimination Kit Ref: HAE-RUSH
FOR RUSH / PRO RIDE CHASSIS
Fits:2010-12 600 Rush2011-12 800 Rush, RMK, Assault & Switchback Assault
SLP Hot Air Elimination Kits help reduce underhood hot air to maintain higher horsepower by delivery additional cold air and hot air escape from the chassis. The kit for the left side helps to keep the clutches running cool, which considerably reduces the chance for performance loss due to heat saturation and improves belt life. The kit for the right side helps to reduce underhood heat given off by the exhaust system. Venta have a powder snow pre-filter that repels snow and water, yet allows air to paas through. These vents are sold in kits for the right and left side.
Each kit includes 3 vents
|
|
Hot Air Elimination Kit
Ref: 32-568
$86.95 | RIGHT SIDE
4 In Stock |
|
Hot Air Elimination Kit
Ref: 32-567
$86.95 | LEFT SIDE(Clutch)
4 In Stock |
|
|
Hot Air Elimination Kits Ref: HAE-KIT-M
FOR ARCTIC CAT M CHASSIS
SLP Hot Air Elimination Kits help reduce underhood hot air to maintain higher horsepower by delivery additional cold air and hot air escape from the chassis. The kit for the left side helps to keep the clutches running cool, which considerably reduces the chance for performance loss due to heat saturation and improves belt life. The kit for the right side helps to reduce underhood heat given off by the exhaust system. Venta have a powder snow pre-filter that repels snow and water, yet allows air to paas through. These vents are sold in kits for the right and left side. Each kit contains a side panel vent and two Flow-Rite Intake Kits
|  |
|
Hot Air Elimination Kit - Right
Ref: 32-530
$88.95 | RIGHT SIDE
(Except M1000)
Instruction Sheet
2 In Stock |
|
Hot Air Elimination Kit - Right
Ref: 32-544
$88.95 | RIGHT SIDE - M1000
Instruction Sheet
0 In Stock |
CURRENTLY OUT OF STOCK |
Hot Air Elimination Kit - Left
Ref: 32-531
$88.95 | LEFT SIDE
Instruction Sheet
1 In Stock |
|
|
Hot Air Elimination Kit Ref: HAE-REV
FOR REV CHASSIS
The REV is in desperate need of additional chassis ventilation to eliminate underhood heat build up. This kit effectively forces cold air into the chassis. It then evacuates the hot air out of the chassis.
Rev Chassis Kit (#14-120) Includes: 2 Flow Rite Intakes and air outlet grate with pre filter
Rev XP Chassis Kits (#32-555 & 32-556) Include: Shock tower, upper side panel and outlet vents with pre filter
|  |
|
Hot Air Elimination Kit
Ref: 14-120
$73.95 | Rev Chassis
(EXCEPT RT)
3 In Stock |
|
Hot Air Elimination Kit
Ref: 32-555
$86.95 | Rev XP Chassis
Left Side (Clutch)
3 In Stock |
|
Hot Air Elimination Kit
Ref: 32-556
$105.95 | Rev XP Chassis
Right Side
1 In Stock |
|
|
High FlowTM Intake Kit Ref: 14-305
For '07-11 M8/Crossfire 800 and M1000/Crossfire 1000 Arctic Cats
The stock M8 and M1000 intake is quite restrictive, primarily in the nose of the hood where the air intake tapers down and connects to the bellows. We have eliminated this restriction by increasing the volume of the air intake in this area. This intake kit further maximizes consistency by utilizing two additional vents that are positioned low and forward. These vents draw in cold dense air, even when the upper outside stock intake vents get partially plugged in deep powder snow. It increases midrange power for better throttle response and delivers anadditional 2 horsepower peak.
Instruction Sheet
22 In Stock
$57.95
|  |
|
|
 | Polaris High FlowTM Intake Kit Ref: INTAKEKIT
The high flow intake kit converts the top of your airbox to increase intake air velocity. This gives more available air volume into the airbox improving atomization efficiency of fuel in turn improving throttle response and delivering and additional 3 hp peak. Good improvement for stock sleds, mandatory for modified ones.
|
|
Intake Kit Ref: 14-107
Edge XC 2000-02
Instruction Sheet
8 In Stock
$47.95
|
|
Intake Kit Ref: 14-115
Edge XC 2003-05
Edge RMK & Pro X/X2/XR '02-05
600 HO IQ 2006-09 (Carb) except RR
Instruction Sheet
14 In Stock
$48.95
|
|
Intake Kit Ref: 14-123
600 HO, 700 HO Cleanfire 2007-12
800 HO 2008-10
Instruction Sheet
6 In Stock
$45.95
|
|
|
 | High FlowTM Intake Kit - Polaris Rush Ref: 14-307
Significant increase to air intake surface area for better airflow to engine.
Fits:2010-12 600 Rush2011-12 800 Rush, RMK, Assault & Switchback Assault2012 600 Switchback & RMK
2 In Stock
$60.95
|
|
|
High FlowTM Intake Kit Ref: HF-INTAKE130
For Polaris 600/700/800 Edge
This High Flow Intake Kit maximizes air flow through the hood and into the engine. It utilizes a Powder Snow Pre-Filter Kit, High Flow Air Horn Kit and two Snap-In Style Flow Rites.
|  |
|
High Flow Intake Kit Ref: 14-130
XC Edge 2000-02
0 In Stock
$127.95
|
CURRENTLY OUT OF STOCK |
High Flow Intake Kit Ref: 14-131
XC Edge 2003-05 / Pro X & RMK 2002-05
1 In Stock
$127.95
|
|
|
 | High FlowTM Intake Kit Ref: HF-INTAKE126
For Polaris 600/700/800 H.O.
This High Flow Intake Kit maximizes air flow through the hood and into the engine. It utilizes a Powder Snow Pre-Filter Kit, High Flow Air Horn Kit and Flow Rites (Four 2" snap-in style in #14-126 & 14-127 and one 2 1/2" in #14-128)
|
|
High Flow Intake Kit Ref: 14-126
600 HO Carb 2006-09
3 In Stock
$166.95
|
|
High Flow Intake Kit Ref: 14-127
600, 700 CFI 2007-08 (except '08 700 RMK)
1 In Stock
$164.95
|
|
High Flow Intake Kit Ref: 14-128
700, 800 CFI RMK '08 / 600 Shift '12 / All IQ Models '09-11
(except Touring, FST and 550/600 Shift Short Track & Rush)
4 In Stock
$85.95
|
|
High Flow Intake Kit Ref: 14-140
Same as #14-128 listed above only this one includes the #14-135 upper dash vent
3 In Stock
$127.95
|
|
|
High Flow Intake Kit Ref: HFIK-REV
FOR REV CHASSIS
The REV's air intake is restrictive and because of its placement it is prone to plugging with powder snow and ice. This High Flow Intake kit doubles the intake surface area for added air flow to the engine. A powder snow pre-filter repels snow and water, reduces the tendency of powder snow and ice plugging by shedding the snow rather than allowing it to build up.
Instruction Sheet
|  |
|
High Flow Intake Kit
Ref: 14-119
$91.95 | Rev Chassis
(EXCEPT RT MODELS)
2 In Stock |
|
High Flow Intake Kit
Ref: 14-129
$73.95 | Rev XP Chassis
4 In Stock |
|
|
 | High FlowTM Air Horn Kit Ref: HF-AIRHORN
This High FlowTM Air Horn Intake kit provides more airflow to your engine, which improves throttle response, peak horsepower and running consistency. A good improvement for stock sleds, mandatory for modified ones.
|
|
High Flow Air Horn Kit
Ref: 14-292
$36.95 | Firecat Models
Instruction Sheet
4 In Stock |
|
High Flow Air Horn Kit
Ref: 14-291
$40.95 | M6 & M7 Chassis(pictured)
Instruction Sheet
6 In Stock |
|
|
Hot Air Venting Kit Ref: VENT-KIT
Reduces under hood heat by up to 30 degreesAllows air to enter in & exit out the backScreens sit low on the body so air will pass through the clutch and exhaust compartmentMost venting holes must be cut outAll screens are black powder coat paintedKit includes special mounting rivits for screens
|  |
|
|
| Polaris Venting Kit
|
Hot Air Venting Kit Ref: 200-271
IQ, RMK & Switchback 2005-10 / Vent Kit - 4 Screens
Instruction Sheet
2 In Stock
$118.95
|
|
Hot Air Venting Kit Ref: 200-272
IQ, RMK & Switchback 2007-10 / Back Kit - 2 Screens
Instruction Sheet
1 In Stock
$56.95
|
|
|
Power Pack Ref: 201-220
FOR POLARIS WITH KEIHIN CARBS. The Power Pack maximizes your power from engagement to top end by utilizing new technology through a series of venturi dividers placed in the carburetor to increase air velocity at different throttle positions. This increased velocity results in better fuel atomization which in turn delivers instant throttle response, improved low end through midrange horsepower and improves fuel economy. Easy to install and tune.
6 In Stock
$67.95
|  |
|
|
 | XP/XR Chassis Support Brace Ref: 183-XPXR
Any knowledgeable clutch tuner will tell you that heat is the enemy of clutches and belts and eliminating it will help performance and longevity of clutching components and those expensive belts! Another often overlooked issue when the secondary tower flexes is the added side load on the chain case bearing and the side plates of the drive chain--again causing more friction which robs more horsepower, add all of this up and every little bit of friction that you can reduce will add up to increased horsepower at the track! This product does not only save on the belts, chassis, and increase hp, the installation will only take 10 minutes. There is no drilling, cutting or modifying your chassis to accept the new chassis brace.
|
|
Support Brace
Ref: 183110
$178.95 | XP Chassis
Instruction Sheet
0 In Stock |
CURRENTLY OUT OF STOCK |
Support Brace
Ref: 183111
$208.95 | XR Chassis
2 In Stock |
|
|
XR Engine Support Ref: 183112
Fits 2009-11 Ski-Doo XR ChassisSupports the engine from pulling up toward the secondary clutchImproves belt and engine mount lifeFully adjustable amount of presetEasy 10 minute installation
3 In Stock
$85.95
|  |
|
|
 | Torque Brace Ref: 12-101
Arctic Cat 800/900 ZR/ZL 2001-05
Stock motor mounts are 'ok' for stock applications, but when you add traction, engine mods, etc more stress is created on these mounts. Engine misalignment, excessive belt wear and inconsistent clutching will be the end result. The torque brace kit will help eliminate these problems. Installs quickly and easily. Includes instructions.
Requires drilling
0 In Stock
$142.95
|
CURRENTLY OUT OF STOCK |
|
Torque Brace Ref: 12-102
Arctic Cat F6/F7 2003-06
Stock motor mounts are 'ok' for stock applications, but when you add traction, engine mods, etc more stress is created on these mounts. Engine misalignment, excessive belt wear and inconsistent clutching will be the end result. The torque brace kit will help eliminate these problems. Installs quickly and easily. Includes instructions.
0 In Stock
$142.95
|  |
CURRENTLY OUT OF STOCK |
|
 | Torque Brace Ref: 12-103
Arctic Cat F8/F1000 2007-11
Stock motor mounts are 'ok' for stock applications, but when you add traction, engine mods, etc more stress is created on these mounts. Engine misalignment, excessive belt wear and inconsistent clutching will be the end result. The torque brace kit will help eliminate these problems. Installs quickly and easily. Includes instructions.
0 In Stock
$142.95
|
CURRENTLY OUT OF STOCK |
|
Engine Torque Arm Ref: 23-68
For 2011-12 Polaris 800 Rush, RMK, Assault, Switchback and Switchback Assault
This new torque arm kit holds the engine in place when under hard acceleration or heavy load. Benefits include better and more consistent horsepower transfer to the ground, lower belt/clutch temperatures, better belt and motor mount life.
3 In Stock
$90.95
|  |
|
|
 | Super Link Ref: SUPERLINK
Best torque link available. State-of-the-art aluminum dampened torque link holds clutch alignment during hard acceleration. It increases belt life, belt performance and transmits less vibration than solid links. Will not work with electric start.
|
|
Super Link Ref: 900-557
97-01 Polaris Indy 800/700/600, XC, SKS, RMK Twins
Instructions
5 In Stock
$76.95
|
|
Super Link Ref: 900-559
'96 Polaris Ultra & XCR 600 Special / '99-01 XCR 700 & 800
Instructions
12 In Stock
$76.95
|
|
Super Link Ref: 900-563
02-05 Polaris 700, 800 Edge XC / RMK / Switchback (big block)
2 In Stock
$79.95
|
|
Super Link Ref: 900-566
2002-04 Polaris 700, 800 Pro X, X2, XR
2 In Stock
$79.95
|
|
Super Link Ref: 900-553
Ski-Doo REV Chassis w/twin cyl engine
0 In Stock
$84.95
|
CURRENTLY OUT OF STOCK |
|
 | Engine Push Arm - Polaris Ref: PUSHARM
The high torque of the new twins create an undesirable movement of the engine. With the use of these push arms, the engine and clutching stays where you want it without increasing vibration.
|
|
Engine Push Arm Ref: 900-830
'97-02 GEN II CHASSIS (pictured)
1 In Stock
$48.95
|
|
Engine Push Arm Ref: 900-832
'00-05 EDGE CHASSIS (Except 600)
3 In Stock
$48.95
|
|
Engine Push Arm Ref: 900-834
'02-04 PRO-X (Except 600)
3 In Stock
$48.95
|
|
Engine Push Arm Ref: 23-62
'06-09 600 HO IQ Carb Models
1 In Stock
$48.95
|
|
Engine Push Arm Ref: 23-63
'07-12 600 HO CFI / '07-10 700 HO CFI / '07-10 800 HO CFI
3 In Stock
$48.95
|
|
|
 | Side Hiller 2 Lefty Kit Ref: 410-409
Universal design (will fit 7/8" OEM handlebars)Extremely easy installation (kit comes pre assembled & there is no modifying necessary). Smooth and easy to pull like the OEM throttle Gets full throttle without having the cable adjusted too tight Parts are CNC machined from billet aluminum Throttle lever is designed for finger use, but can also be used with your thumb Sealed cable helps to keep condensation out (prevents freezing) Throttle lock-out pin (for safer loading onto trailer) Will work with hand guards.
Instruction Sheet
Click here to see more photos
11 In Stock
$99.95
|
|
|
SNOBUNJE "THROTTLE LOGIC" Left-Hand Throttle Ref: 119-992
Quick-Release cable disconnectEasy installationClamps over hand gripUniversal installationAdjustable cable bracketSnow & ice guardDoes not compromise OEM throttle sensorsIncreases throttle hand positionsReduces throttle hand fatigue
Product Manual
0 In Stock
$156.95
|  |
CURRENTLY OUT OF STOCK |
|
 | Throttle Flare - BLACK Ref: 119-990
Using the Throttle Flare, you will be able to apply a quicker and more consistent throttle response using several new throttle hand positions, greatly improving your ability to apply your body weight where needed in the steering effort. Trail riders will find that the Throttle Flare allows them to bring their thumb back to a normal position and push the throttle lever using the top flare and the ball of their hand. This helps reduce hand fatigue. The Throttle Flare is easly installed using one mounting screw.
More Photos
51 In Stock
$12.95
|
|
|
Exhaust Valve Pop Up's Ref: POPUPS
For Polaris & Ski-DooEasy and quick system to insure proper operation of exhaust valvesExhaust valve engines require cleaning of the exhaust valves on a regular basis. Depending upon oil used, jetting and type of riding, valve maintenance may be needed at 500 to 2000 milesSmall, CNC machined plug fits over exhaust valve using stock components. When engine is run on stand, Pop-Up Plug will pop up when exhaust valves open. If plugs do no pop up smoothly and in sync, maintenance is dueAllows quick visual checks of improperly working valves to prevent engine damageValves that move freely and are in synchronization guarantee better throttle response, better mileage, and more horsepowerSimple installation with hand toolsFor exhaust valve engines only
Installation Instructions
|  |
|
Exhaust Valve Pop Ups
Ref: 911-003
$18.95 | SKI-DOO
Twins with non electonic valves
3 In Stock |
|
Exhaust Valve Pop Ups
Ref: 911-006
$18.95 | POLARIS
Twins 2000-03
4 In Stock |
|
|
 | TPI Valve - Total Performance Intake Ref: TPIVALVE
The TPI Valve is designed to increase air flow into your air box and carburetors. This is one of the fastest and easiest ways to increase performance. The patent pending TPI Valve is totally adjustable, allowing you to determine exactly how much to increase air flow. We call this "air jetting". Air passing through the TPI Valve is filtered by an internal filter in the TPI Valve. Easy to use and install, the TPi Valve is 1 1/2" diameter and 1 1/2" high. One valve recommended per 200cc.
|
|
TPI Valve
Ref: 201-219
$37.95 | PAIR
0 In Stock |
CURRENTLY OUT OF STOCK |
|
 | TPI Valve Low Boy Ref: LOWBOY
Same as TPI Valve above, however the Low Boy is 2 5/8" square and mounts flush on the airbox. Sold individually.
|
|
Low Boy
Ref: 201-215
$18.95 | BLACK
6 In Stock |
|
|
 | Upper Dash Vent Ref: 14-135
For Polaris IQ Models
This vent provides an additional 30% surface area to increase the amount of air available to the engine on stock or modified sleds. It is highly recommended when riding in powder snow conditions. It features an attractive plastic grate which utilizes a special pre-filter material that repels snow and water yet maintains high airflow.
2 In Stock
$34.95
|
|
|
Footwell Vents Ref: 32-552
For Polaris 2007-11 RMK RAW Chassis
This Footwell Vent Kit helps to remove hot underhood heat from the chassis. These vents reduce the chance for performance loss due to heat saturation for a more consistent running engine. They are installed just above the footwells and are sold as a set, one right and one left hand vent.
2 In Stock
$67.95
|  |
|
|
 | Side Panel Vent Kit Ref: 20050
Arctic Cat
Allows hot under hood air out without allowing snow in. Includes both right and left sides. Easy installation.
Fits: M Series and Crossfire models 2005-11
2 In Stock
$56.95
|
|
|
PowAirTM Intake Vents Ref: POWAIR-VENT
Low cost design for a cheaper alternative to the competition100% digestable materialsIntake screen for debris protectionPlastic construction prohibits icing and stickingEasy hole-saw installationExtremely low cracking pressure ensures the engine does not bogThe 3 inch vent has nearly 2x the flow volume as the competition (the 2 inch is comparable)
|  |
|
PowAir Intake Vent
Ref: 201227
$10.95 | 2" Vent
15 In Stock |
|
PowAir Intake Vent
Ref: 201228
$13.95 | 3" Vent
12 In Stock |
|
|
 | Flow-Rite Ref: 14-258
FOR SPEEDO OR TACH HOLE. This 4" pre-filter was designed to replace the speedometer to allow more cold air flow into the intake tract for more air box feed. Made with a powder snow pre-filter that repels snow and water, yet passes air right through. Requires 4 1/2" hole for installation.
6 In Stock
$35.95
|
|
|
Flow-Rite Intake Kits Ref: 14-FLOWRITE
Eliminate air intake restrictions by installing the Flow-Rite in the dash or intake tract for more air box feed. The Flow-Rite is supplied with a powder snow pre-filter that repels snow and water, yet passes air right through. A must for modified sleds. Sold individually. These 2 are made using a rubber flange to attach the Flow-Rite to the surface that it is being installed in. This rubber flange conforms itself to a wide variety of contoured, shaped and textured surfaces for a universal mounting system.
|  |
|
Flow-Rite Intake Kit Ref: 14-189
2 1/2" ID x 3 5/8" OD (Required Hole Size = 3 1/8")
Instruction Sheet
31 In Stock
$20.95
|
|
Flow-Rite Intake Kit Ref: 14-194
2" ID x 2 11/16" OD (Required Hole Size = 2 3/8")
Instruction Sheet
13 In Stock
$20.95
|
|
|
 | Flow-Rite Intake Kit Ref: 14-197
Same as Flow-Rite Intake Kit above except this one is designed for ease of installation on flat or nearly flat surfaces. It requires a 2 1/2" size hole saw which is readily available from any hardware store. Installatin is a snap: hole saw the hole (2 1/2" hole required), debur the edges, clean hole saw shavings and snap Flow-Rite into place. 2" ID x 2 3/4" OD. Sold individually.
Instruction Sheet
3 In Stock
$20.95
|
|
|
BullsEye Air Intakes Ref: 201-224
D&D's Bullseye Air Intakes are great for any air box; snowmobile or ATV. The principle is simple: more air = more power. Just drill a 1 1/2" hole and press in for more air flow. In most cases, adding performance parts such as pipes, reeds or big bores makes the stock air box insufficient. By adding the Bullseye Air Intakes, you can greatly improve air flow. The intakes come in a package of six. Available only in black.
9 In Stock
$40.95
|  |
|
|
 | High Flow Outside Draw Conversion Kit Ref: 14-206
For these models only2001-02 800 ZR, ZL & Mtn Cat2003 900 ZR
Transform your stock air box into a high flowing, cold air drawing horsepower enhancing intake system. Features include:Increases air intake surface area by 30% allowing more airflow to engineAttractive brushed aluminum intake grate that mounts to your hoodUnique filter material keeps powder snow and water out of the air boxCold air draw to provide more dense oxygen rich air to the engineWill not plug easily in deep powder snow conditionsShifts stock toolbox and CDI forwardEasy installationFor carb models only
Instruction Sheet
1 In Stock
$110.95
|
|
|
High Flow Airbox - Outside Air Draw Style Ref: 200-259
FOR 1997-01 600 (non VES), 700 & 800 TWINS, XC, SKS & RMK (except Edge chassis models)
Kit adapts to the stock bottom box to increase airflow. 4 hp peak and 5 hp midrange increase.
3 In Stock
$86.95
|  |
|
|
 | High Flow Air Box Kit Ref: 14-288
For 2005-06 Polaris 700/900 IQ Chassis
This High Flow Air Box kit increases cold air delivery to the engine by reducing air intake restriction. This increased air flow results in a substantial increase in throttle response, more horsepower and improved running consistency. Not only does it deliver an additional 4 horsepower, but it also sheds an amazing 7-8 pounds of weight. This kit also comes with a new aluminum belt guard that allows air in and around the clutches for cooler running, better consistency and increased belt life. Fusion (not RMK or Switchback)
Instruction Sheet
2 In Stock
$295.95
|
|
